2 x 50W + 100W 2.1 Channels SPDIF Coaxial+DSP Amplifier Board - TSA7800C
20 or more $60.00
TSA7800C 2x50W + 100W 2.1 channels SPDIF+DSP digital amplifier board with a SPDIFBee receiver module. SPDIFBee convert the SPDIF signal to I2S signal and output to the ADAU1701 DSP chip. TSA7800C is a very flexible DSP/DAC/Amplifier combination board. It has perfect class-D architecture(Based on TPA3116D2) and 2 channels have 50W power output and another one channel has 100W power output. All the channels are capable of outputting nominal power simultaneously and continuously. This board can be powered by any DC12V-24V power supply. It can be used to drive any 4Ω or 8Ω passive speakers(Subwoofer channel can drive 2Ω speaker).
It's a 2.1 channels amplifier board. That channel for subwoofer are 100W mono output(User can change the DSP program to let it becomes right or left channel). It has a coaxial input connector on the board which can accept different sampling rates digital audio source, from 16bit 44.1KHz to 26bit 96KHz. The highlight point is ADAU1701 DSP chip on board. User can set each channel audio tones separately.
External Buttons port:
Not support this function on TSA7800C.
Aux in enable port:
The default DSP program are mix the RCA/Bluetooth audio and output to the amplifier chips. If you want select the RCA/SPDIF manually by a switch. You can connect an external switch to this port and load a different DSP program.
POT port:
User can connect an external 10K potentiometer to control the audio volume.
DSP programming port:
User can load a new DSP program by using the USBi JTAG Sigma DSP programmer
The onboard default DSP program will mix the RCA&SPDIF audio and output to the speakers. User can also change the DSP program to let the audio source selectable by an external switch.
Specification:
Specifications typical @ +25℃, Powered by 30V DC, unless otherwise noted. Specifications subject to change without notice.
| Parameter | Condition | Min | Typ | Max |
|
Supply Voltage (VDC) |
- | 12 | 21 | 24 |
| Power output per channel | RL= 4Ω, 10% THD+N | 50W | ||
| RL= 8Ω, 10% THD+N | 30W | |||
| RL= 4Ω, 10% THD+N | 18W | |||
| 100W channel: RL= 2Ω, 1% THD+N | 100W | |||
| THD+N | @4Ω, 1W, 1KHz | 0.03% | ||
| Bandwidth @ ±3dB | @4Ω | 20Hz | - | 20KHz |
| Input Impedance | - | - | 22KΩ | - |
|
Minimum Load Impedance |
3.2Ω |
|
||
| Gain | 18dB | 24dB | 34dB | |
| Efficiency | 50W @ 4Ohm | 87% | - | 92% |
Features:
- Size: 13.5cm x 9.2cm x 3.4cm
- SPDIF Supported sampling rate:
- 16bit, 44.1KHz, 48KHz, 88.2KHz, 96KHz
- 24bit, 44.1KHz, 48KHz, 88.2KHz, 96KHz
- I2S Sampling Rate: 48KHz, 16bit
- 2.1 channels
- Working voltage: DC12V-24V
- Over/under voltage protection
- Over current protection
- Over temperature protection
Applications:
- Personal computer
- Background music system
- Musical instrument amplifiers
- Home DIY
- Car audio
Documents:
Write a review
Your Name:Your Review: Note: HTML is not translated!
Rating: Bad Good
Enter the code in the box below:
